01

Introduction to Current Electricity

These current electricity class 12 notes take you from the flow of charge to solving full circuits: electric current and current density, drift velocity and mobility, Ohm’s law, resistivity and its temperature dependence, electrical power, combinations of resistors and cells, internal resistance, Kirchhoff’s rules, and the Wheatstone and metre bridges. Current electricity is one of the most numerical chapters of NEET Physics, so every section below ends with the formula you will actually use.

Chapter at a glance
  • Core ideas: current and current density, drift velocity, Ohm’s law, resistivity, temperature dependence, power, series and parallel combinations, emf and internal resistance, Kirchhoff’s rules, Wheatstone bridge, metre bridge
  • Key formulas: I = neAvd; vd = eEτ/m; ρ = m/(ne2τ); R = ρl/A; P = VI = I2R = V2/R; V = E − Ir; P/Q = R/S
  • Most tested in NEET: equivalent resistance, stretched-wire problems, drift velocity, internal resistance and terminal voltage, power in series and parallel, Kirchhoff’s rules, balanced Wheatstone bridge
  • Free PDF: full chapter notes in our study app (link below)

In Electrostatics, charges are at rest. In current electricity, charges move steadily through conductors, and that steady flow lights our homes, runs every battery-powered device and carries signals in our nerves. The chapter is about how fast charge flows, what opposes it, and how energy is delivered in a circuit.

Tip

Before attempting numericals, redraw every circuit neatly and mark the junctions. Most circuit mistakes come from misreading which resistors are actually in series or in parallel.

Key insight: current electricity class 12 notes rest on two ideas: charge is conserved at every junction, and energy is conserved around every loop.

02

Electric Current and Current Density

Electric current is the rate of flow of electric charge through a cross-section of a conductor. Its SI unit is the ampere (1 A = 1 C s−1). By convention, the direction of current is the direction in which positive charge would flow, so in a metal it is opposite to the motion of the electrons. Every later formula in current electricity class 12 notes builds on this definition.

Electric current
Steady current: I = q / t Instantaneous current: I = dq / dt

Current is a scalar quantity, despite having a direction: currents at a junction add algebraically, not as vectors. Current density, on the other hand, is a vector.

Current density: j = I / A (unit A m⁻²)

The direction of j is the direction of the electric field (the flow of positive charge).

Direct and Alternating Current

  • Direct current (DC): the flow of charge stays in one direction. Typical of batteries and cells.
  • Alternating current (AC): the direction of charge flow reverses periodically. This is the supply in our homes.

Key insight: in current electricity class 12 notes, current is a scalar but current density is a vector; NEET statement questions often test exactly this difference.

03

Drift Velocity, Mobility and Relaxation Time

In the absence of an electric field, free electrons in a metal move randomly with high thermal speeds and collide with the ions, but their average velocity is zero, so there is no net current. When a field E is applied, each electron is accelerated opposite to E between collisions and gains a small average velocity in that direction: the drift velocity (vd). This is one of the most concept-rich topics in current electricity class 12 notes.

Drift velocity and current
v_d = eEτ / m (directed opposite to E) I = neAv_d j = nev_d
  • Relaxation time (τ): the average time between two successive collisions of an electron. For metals it is of the order of 10−14 s.
  • Number density (n): the number of free electrons per unit volume of the conductor.
  • Mobility (μ): drift velocity per unit electric field, μ = |vd| / E = eτ/m. SI unit m2 V−1 s−1.
Warning

Drift velocity is very small (around 10−4 m s−1 in a typical wire), yet a bulb lights the moment the switch is pressed. That is because the electric field is set up through the whole circuit almost instantly, and the electrons everywhere start drifting together.

Key insight: current electricity class 12 notes link the microscopic and the measurable through I = neAvd; for the same current, a thinner wire means a larger drift velocity.

04

Ohm’s Law, Resistivity and Conductivity

Ohm’s law states that, at constant temperature and other physical conditions, the potential difference V across a conductor is directly proportional to the current I through it. The constant of proportionality is the resistance R, measured in ohms (Ω). Ohm’s law is the starting point of most circuit numericals in current electricity class 12 notes.

Ohm’s law and resistance
V = IR R = ρl / A Vector form: j = σE, where σ = 1/ρ

Resistance depends on the length and area of the conductor, but resistivity (ρ) is a property of the material alone (at a given temperature). Its unit is Ω m; conductivity σ is measured in S m−1. Combining the drift velocity result with Ohm’s law gives the microscopic formula:

ρ = m / (ne²τ) ; σ = ne²τ / m

Resistivity depends on the number density of free electrons and the relaxation time.

Material typeTypical resistivity (Ω m)Examples
Conductors (metals)10−8 to 10−6Silver, copper, aluminium
SemiconductorsIntermediate, falls as temperature risesSilicon, germanium
Insulators1014 or moreGlass, rubber, quartz

Limitations of Ohm’s Law

Ohm’s law is not a universal law. Materials and devices that do not obey it are called non-ohmic. The deviations are of three kinds:

  • V stops being proportional to I (the V–I graph is not a straight line), as in a filament bulb, where resistance rises with temperature.
  • The relation depends on the sign of V: reversing V changes the magnitude of the current, as in a semiconductor diode.
  • The relation is not unique: the same current can occur at more than one voltage, as in gallium arsenide.
Tip

If a wire is stretched to n times its length, its volume stays the same, so its area becomes 1/n times. The new resistance is n2 times the original: double the length means 4 times the resistance, not 2 times. Its resistivity does not change.

Key insight: current electricity class 12 notes separate R (depends on shape) from ρ (depends on material and temperature); most NEET traps hinge on this.

05

Temperature Dependence of Resistivity

As temperature increases, the ions in a metal vibrate more, electrons collide more often, τ falls and resistivity rises. For semiconductors and insulators the story is different: their resistivity decreases as temperature rises, because many more charge carriers (larger n) become available, which outweighs the drop in τ. Current electricity class 12 notes compare the two trends below.

Temperature coefficient of resistivity
ρ_T = ρ₀ [1 + α(T − T₀)] R_T = R₀ [1 + α(T − T₀)] (approximately)
  • Metals: α is positive; resistivity rises with temperature.
  • Semiconductors: α is negative; resistivity falls with temperature.
  • Alloys such as nichrome, manganin and constantan have very weak temperature dependence, so they are used in standard resistors.

Key insight: current electricity class 12 notes explain both trends with ρ = m/(ne2τ): in metals τ falls with temperature, in semiconductors n rises much faster.

06

Electrical Energy and Power

When current flows through a resistor, the electrical energy given to the charges is converted into heat. This is called Joule heating. For NEET, you must be comfortable switching between the power formulas depending on which quantity stays constant in the circuit. Current electricity class 12 notes summarise them here.

Power and energy
P = VI = I²R = V²/R Energy W = Pt = I²Rt 1 unit = 1 kWh = 3.6 × 10⁶ J
  • For resistors in series (same I), use P = I2R: the larger resistance dissipates more power.
  • For resistors in parallel (same V), use P = V2/R: the smaller resistance dissipates more power.

Power Transmission

Power P is sent to a town through cables of resistance Rc. The current is I = P/V, so the power wasted in the cables is Pc = P2Rc/V2. Transmitting at a very high voltage cuts this loss, which is why power lines carry high voltages and step-down transformers are used near homes. This is a common application question from current electricity class 12 notes.

Key insight: current electricity class 12 notes on power have one rule of thumb: same current, think I2R; same voltage, think V2/R.

Read the topic? Try the NEET previous year questions from Current Electricity next, with answers.

Practice Current Electricity PYQs
07

Combination of Resistors

Complex circuits can usually be simplified by identifying resistors in series or parallel. In series the current is the same; in parallel the voltage is the same. Mastering these combinations is essential for most circuit numericals in current electricity class 12 notes.

FeatureSeries combinationParallel combination
Equivalent resistanceReq = R1 + R2 + …1/Req = 1/R1 + 1/R2 + …
Current (I)Same for all resistorsDivides among branches, more through the smaller resistance
Voltage (V)Divides across resistors, more across the larger resistanceSame for all resistors
Req compared with each RLarger than the largestSmaller than the smallest
n equal resistors RnRR/n
Two resistors in parallel: R_eq = R₁R₂ / (R₁ + R₂)

Current divider: I₁ = I × R₂ / (R₁ + R₂).

Key insight: current electricity class 12 notes give a quick sanity check: series always increases resistance, parallel always decreases it.

08

Cells, EMF and Internal Resistance

A cell maintains a potential difference using chemical energy. Its emf (E) is the potential difference between its terminals when no current is drawn. A real cell has some internal resistance (r) from its electrolyte, so when it supplies a current I, the terminal voltage V is less than E. An ideal cell has zero internal resistance. In current electricity class 12 notes, these three equations cover almost every cell numerical:

Cell in a circuit
Discharging: V = E − Ir Current with external R: I = E / (R + r) Charging: V = E + Ir

Combination of Cells

ArrangementEquivalent emfEquivalent internal resistance
Two cells in seriesEeq = E1 + E2 (E1 − E2 if one is reversed)req = r1 + r2
Two cells in parallelEeq = (E1r2 + E2r1) / (r1 + r2)req = r1r2 / (r1 + r2)
n identical cells in seriesnEnr; current I = nE / (R + nr)
m identical cells in parallelEr/m; current I = E / (R + r/m)
Warning

When cells are in parallel, their internal resistances combine in parallel, not in series. And when a cell is being charged, its terminal voltage is more than its emf.

Key insight: current electricity class 12 notes treat internal resistance as just another resistor in series with the cell; draw it in, and the circuit becomes routine.

09

Kirchhoff’s Rules for Complex Circuits

When series and parallel rules are not enough, Kirchhoff’s rules can solve any circuit. They are the most powerful tools in current electricity class 12 notes.

  • Junction rule (first rule): at any junction, the sum of currents entering equals the sum of currents leaving (ΣI = 0). It follows from conservation of charge.
  • Loop rule (second rule): the algebraic sum of changes in potential around any closed loop is zero (ΣΔV = 0). It follows from conservation of energy, because the electric field is conservative.
Sign convention for the loop rule

Going through a resistor in the direction of the assumed current: −IR. Against it: +IR. Through a cell from − to +: +E. From + to −: −E.

Tip

Assume a direction for each unknown current and stick with it. If an answer comes out negative, the current simply flows the other way; the magnitude is still correct.

Key insight: current electricity class 12 notes reduce Kirchhoff problems to bookkeeping: one equation per independent junction and one per independent loop.

10

Wheatstone Bridge and Metre Bridge

A Wheatstone bridge has four resistors P, Q, R and S arranged in a diamond, with a battery across one diagonal and a galvanometer across the other. It works on the null-point principle: when the bridge is balanced, no current flows through the galvanometer. Applying Kirchhoff’s rules gives the balance condition used throughout current electricity class 12 notes.

Balanced Wheatstone bridge
P / Q = R / S (galvanometer current = 0)

In a balanced bridge, the galvanometer arm can be removed (or the galvanometer and battery interchanged) without changing anything, which makes many “complex” NEET circuits easy to simplify.

Metre Bridge

The metre bridge is a practical Wheatstone bridge in which two of the arms are the two parts of a uniform 1 m wire. With an unknown resistance X in one gap and a known resistance R in the other, the jockey is moved along the wire until the galvanometer shows no deflection. If the balance point is at length l (in cm) from the end next to X:

X / R = l / (100 − l)

The result is most accurate when the balance point lies near the middle of the wire.

Key insight: current electricity class 12 notes treat the bridge as a shortcut: check P/Q = R/S first, and if it holds, drop the middle resistor.

11

The Potentiometer (Background)

Note

The potentiometer has been removed from the current NEET syllabus and the rationalised NCERT book. It is kept here briefly for background, so give it the least revision time.

A potentiometer is a long uniform wire carrying a steady current, so the potential drop along it is proportional to length (V ∝ l). At the balance point it draws no current from the cell being measured, which is why it measures emf more accurately than a voltmeter. Its sensitivity is increased by using a longer wire or a smaller current (a smaller potential gradient).

Comparing emfs: E₁ / E₂ = l₁ / l₂

Internal resistance of a cell: r = R (l₁ − l₂) / l₂.

Key insight: in current electricity class 12 notes for NEET, spend potentiometer time only on the idea of zero current at balance, which also explains the Wheatstone and metre bridges.

12

How NEET Tests This Chapter

Questions from current electricity class 12 notes are mostly short numericals, with some statement-based questions on drift velocity and Ohm’s law.

Question typeWhat to do
Equivalent resistance of a networkLook for series, parallel and balanced-bridge parts; use symmetry.
Stretched or reshaped wireKeep volume constant; R ∝ l2 for stretching.
Drift velocity and mobilityUse I = neAvd and vd = eEτ/m.
Terminal voltage and cell combinationsInclude internal resistance; use V = E − Ir.
Power and bulbs in series or parallelFind each bulb’s R from its rating, then use I2R or V2/R.
Kirchhoff’s rulesWrite junction and loop equations with consistent signs.

The best way to build speed is to practise Current Electricity NEET PYQs here, free and with answers.

Common Mistakes to Avoid

  • Unit conversion: forgetting to convert kWh to joules, or cm and mm2 to m and m2 in resistivity problems.
  • Cells in parallel: adding internal resistances in series instead of in parallel.
  • Junction signs: mixing up positive and negative signs for entering and leaving currents.
  • Stretched wire: forgetting that volume is constant, so area changes inversely with length.

Key insight: current electricity class 12 notes reward a neat redrawn circuit more than any shortcut formula.

13

Current Electricity Class 12 Notes: Summary

Use this checklist for a last revision of current electricity class 12 notes before a test.

Revision Checklist – Current Electricity Class 12 Notes
  • Current I = neAvd (n is the number density of free electrons); current is a scalar, current density j is a vector.
  • Drift velocity vd = eEτ/m; mobility μ = vd/E = eτ/m.
  • Resistance R = ρl/A depends on length and area; resistivity ρ = m/(ne2τ) depends only on material and temperature.
  • Stretching a wire n times: resistance becomes n2 times.
  • Metals: T↑ ρ↑ (α positive); semiconductors: T↑ ρ↓ (α negative).
  • P = VI = I2R = V2/R; 1 kWh = 3.6 × 106 J.
  • Series: same current, Req = ΣR; parallel: same voltage, 1/Req = Σ1/R.
  • Terminal voltage V = E − Ir while discharging, V = E + Ir while charging.
  • Kirchhoff’s first rule: conservation of charge; second rule: conservation of energy.
  • Balanced Wheatstone bridge: P/Q = R/S (galvanometer current = 0); metre bridge: X/R = l/(100 − l).
  • An ammeter is a galvanometer with a low-resistance shunt in parallel; a voltmeter is a galvanometer with a high resistance in series.
Download Current Electricity Class 12 Notes PDF Free in our study app – use code DOCTOR

Frequently Asked Questions – Current Electricity Class 12

Why is current considered a scalar quantity?
Even though current has a direction, it does not follow the laws of vector addition. The total current at a junction is simply the algebraic sum of the individual currents, not their vector sum. Current density, by contrast, is a vector.
What is the main advantage of a Potentiometer over a Voltmeter?
A voltmeter draws some current from the circuit to show a reading, which slightly changes the potential difference it is measuring. A potentiometer at the null point draws zero current, giving an exact measurement of emf. Note that the potentiometer is no longer in the NEET syllabus, so treat this as background in current electricity class 12 notes.
How does stretching a wire affect its resistivity?
Resistivity is an intrinsic property of the material. Stretching a wire changes its length and area (and so its resistance), but the resistivity stays the same as long as the material and temperature are unchanged. Current electricity class 12 notes use this in every stretched-wire problem.
What is the condition for a balanced Wheatstone bridge?
The bridge is balanced when the potentials at the two middle points are equal, so no current flows through the galvanometer. Mathematically, P/Q = R/S, which means the products of opposite resistances are equal (PS = QR). Current electricity class 12 notes derive this from Kirchhoff’s rules.
Why does a bulb glow instantly if drift velocity is so small?
The electric field spreads through the whole circuit at nearly the speed of light, so free electrons everywhere in the wire, including inside the bulb filament, start drifting almost at once. No electron has to travel from the switch to the bulb, as current electricity class 12 notes explain under drift velocity.
Why does the terminal voltage of a cell fall when it supplies more current?
Some of the emf is used to drive current through the cell’s own internal resistance. Since V = E − Ir, a larger current I means a larger drop Ir inside the cell and a smaller terminal voltage, a standard result in current electricity class 12 notes.
Where can I download current electricity class 12 notes PDF?
The complete current electricity class 12 notes PDF is free in our NEET study app. Open the app here and use code DOCTOR to unlock the free study material.
Where can I practise NEET previous year questions on Current Electricity?
You can practise Current Electricity NEET PYQs here, free and with answers. Start with equivalent resistance and stretched-wire questions, then move to internal resistance, power in bulbs, Kirchhoff’s rules and the Wheatstone bridge.